3.1 Pre-Installation Checks

Before installing the Mira Advance ATL Thermostatic Shower‚ ensure the water supply is mains-fed cold water only. Verify that the electrical supply matches the shower’s wattage requirements. Check for any existing system compatibility and ensure the water pressure meets the recommended specifications. It is crucial to review all components and ensure they are undamaged. Additionally‚ confirm that the installation location adheres to all safety guidelines and manufacturer recommendations to guarantee proper function and safety. Proper preparation ensures a smooth installation process.

3.2 Isolating Electrical and Water Supplies

Before starting the installation‚ ensure both electrical and water supplies are completely isolated. Switch off the mains power supply and close the water supply valves. Verify that the electricity supply is turned off using a multimeter. Similarly‚ check that water flow to the shower is halted. This ensures a safe working environment and prevents any accidental activation during installation. Always follow these steps to avoid potential hazards and comply with safety guidelines. Proper isolation is critical for safe and effective installation.

3.4 Recommended Water Supply Configuration

The Mira Advance ATL Thermostatic Shower is designed for use with mains-fed cold water supplies only. Ensure a stable water supply pressure between 1 and 5 bar for optimal performance. Connect the cold water supply to the designated inlet‚ avoiding direct connection of hot water. Use a single-check valve to prevent backflow and ensure compliance with plumbing regulations. Proper configuration ensures efficient operation and prevents potential damage to the system. Always follow the manufacturer’s guidelines for water supply setup.

Operating the Mira Advance ATL Thermostatic Shower

Operate your Mira Advance ATL Thermostatic Shower by adjusting the temperature control dial to your preferred setting. Always follow the instructions provided in the user guide for safe and efficient use.

4.1 Understanding the Thermostatic Control

The Mira Advance ATL Thermostatic Shower features a sophisticated temperature control system designed for precise and safe temperature regulation. The thermostatic valve ensures consistent water temperature‚ even when water pressure fluctuates. This system prevents sudden changes in temperature‚ reducing the risk of scalding. The adjustable temperature limit allows users to set a maximum preferred temperature‚ enhancing safety and personalized comfort. Always refer to the user guide for specific instructions on adjusting and maintaining the thermostatic control for optimal performance.

4.2 Adjusting the Temperature

Adjusting the temperature on the Mira Advance ATL Thermostatic Shower is straightforward and safe. Use the temperature control dial to set your preferred water temperature. Ensure the shower is turned off before making adjustments. Always check the water temperature before use to avoid discomfort. For precise control‚ gently turn the dial to your desired setting. Refer to the user guide for detailed instructions on temperature adjustment and safety precautions to ensure optimal performance and comfort during use.

4.3 Daily Use and Operation Tips

For optimal performance‚ start the shower by turning on the water supply and adjusting the temperature control dial to your preferred setting. Always check the water temperature before stepping in to ensure comfort. To maintain efficiency‚ use the thermostatic control to regulate flow and temperature effectively. Regularly clean the showerhead to prevent mineral buildup. Avoid sudden temperature changes to ensure a stable showering experience. Follow these tips to enjoy a safe‚ comfortable‚ and energy-efficient showering experience with the Mira Advance ATL Thermostatic Shower.

Maintenance and Care

Regular cleaning and inspections are crucial to maintain optimal performance. Clean the showerhead and components to prevent mineral buildup and ensure proper water flow. Check for worn parts and replace them promptly to avoid leaks or reduced efficiency. Descaling the system periodically will help maintain hygiene and performance. Regular maintenance ensures a safe‚ efficient‚ and enjoyable showering experience.

5.1 Cleaning the Showerhead and Components

Regular cleaning is essential to maintain the performance and hygiene of your Mira Advance ATL Thermostatic Shower. Start by descaling the showerhead to remove mineral buildup‚ ensuring optimal water flow. Use a soft cloth and mild detergent to wipe down visible components‚ avoiding abrasive materials that may damage surfaces. Check and clean the filter periodically to prevent debris accumulation. For tougher stains‚ soak the showerhead in a vinegar solution. Regular cleaning prevents biofilm formation and ensures a safe‚ efficient showering experience. Always dry components after cleaning to prevent water spots.

5.2 Checking and Replacing Worn Parts

Regularly inspect the showerhead‚ seals‚ and O-rings for signs of wear or corrosion. Replace any worn components immediately to prevent leaks or reduced performance. Use genuine Mira replacement parts to ensure compatibility and longevity. For optimal maintenance‚ soak removable parts in a mild vinegar solution to remove mineral deposits. Always isolate water and electrical supplies before performing any repairs. Replace the filter periodically to maintain water quality and flow. Regular checks and timely replacements will extend the lifespan of your Mira Advance ATL Thermostatic Shower and ensure consistent performance.

5.3 Preventing Biofilm Formation

To prevent biofilm formation‚ ensure the water supply to your Mira Advance ATL Thermostatic Shower is clean and free from debris. Regularly clean the showerhead and internal components with a mild descaler or vinegar solution. Replace filters as recommended to reduce mineral buildup. Dry the showerhead and handles after use to inhibit microbial growth. For added protection‚ consider installing a water treatment system to minimize impurities. Regular maintenance will help maintain hygiene and performance‚ ensuring a safe and enjoyable showering experience. Always use genuine Mira parts for replacements to guarantee compatibility and effectiveness.

Troubleshooting Common Issues

This section helps identify and resolve common problems with your Mira Advance ATL Thermostatic Shower‚ such as temperature fluctuations or low water pressure‚ ensuring optimal performance.

6.1 Diagnosing Temperature Fluctuations

Temperature fluctuations in your Mira Advance ATL Thermostatic Shower can occur due to inconsistent water supply or faulty thermostat function. Check if the water pressure is stable and ensure the thermostat is clean. Verify electrical connections and inspect for any blockages in the pipes. If issues persist‚ refer to the troubleshooting section for detailed solutions or contact Mira customer support for professional assistance.

6.2 Addressing Low Water Pressure

Low water pressure can affect the performance of your Mira Advance ATL Thermostatic Shower. To address this‚ check for blockages in the inlet pipes and ensure the water supply configuration matches the recommended specifications. Verify that the water pressure meets the minimum requirements outlined in the User Guide. If issues persist‚ clean the showerhead and check for any kinks or obstructions in the hoses. For further assistance‚ consult the troubleshooting section or contact Mira customer support.

6.3 Resolving Electrical Connectivity Problems

If you experience electrical connectivity issues with your Mira Advance ATL Thermostatic Shower‚ first ensure all connections are secure and properly installed. Check the circuit breaker or fuse box to confirm the power supply is intact. Verify that the isolator switch is in the “on” position. If problems persist‚ consult a qualified electrician to inspect the wiring and connections. Always ensure the electricity supply is switched off before attempting any repairs or adjustments. For further guidance‚ refer to the troubleshooting section or contact Mira customer support.

Additional Features and Settings

Discover advanced features like Heatloop Technology for optimal water heating and eco-friendly settings to reduce energy consumption‚ enhancing your showering experience with customizable temperature and flow controls.

7.1 Heatloop Technology Benefits

The Mira Advance ATL features innovative Heatloop Technology‚ designed to optimize water heating efficiency. This system ensures consistent temperature delivery while minimizing energy consumption. By reducing heat loss‚ it provides a more eco-friendly showering experience. The technology also helps maintain stable water temperatures‚ even during fluctuations in water pressure. Additionally‚ Heatloop Technology contributes to lower energy bills and a reduced environmental impact‚ making it a sustainable choice for modern households. This feature enhances overall performance and user satisfaction‚ offering a reliable and efficient showering solution.

7.2 Eco-Friendly and Water-Saving Tips

Optimize water efficiency with the Mira Advance ATL by using its eco-friendly settings. Lowering the temperature slightly can significantly reduce energy consumption. Take shorter showers to conserve water. Regularly check for leaks to prevent waste. Use the shower’s flow-control features to minimize water usage without compromising comfort. These practices not only benefit the environment but also lower utility bills‚ making your showering experience more sustainable and cost-effective.

7.3 Customizing Showering Experience

The Mira Advance ATL Thermostatic shower allows for a personalized experience. Adjust the temperature precisely to your preference using the thermostatic control. Utilize the flow-control features to customize water flow‚ ensuring comfort and efficiency. Explore different spray patterns on the showerhead to enhance your showering experience. Regular maintenance‚ like cleaning the showerhead‚ ensures optimal performance. These features empower you to tailor your shower to your needs‚ combining comfort‚ efficiency‚ and enjoyment seamlessly. Customize your shower experience with ease and precision.

Warranty and Customer Support

For warranty details‚ register your Mira Advance ATL Thermostatic shower. Contact Mira Customer Service for assistance or inquiries. Warranty terms ensure coverage for defects and repairs.

8.1 Warranty Terms and Conditions

The Mira Advance ATL Thermostatic shower is backed by a comprehensive warranty program. The warranty covers manufacturing defects for a specified period‚ ensuring your investment is protected. Proper installation is required for warranty validity. Register your product to activate coverage. Terms and conditions may vary‚ so refer to the official Mira website or contact customer support for detailed information. Always retain your proof of purchase for warranty claims.

8.2 Contacting Mira Customer Service

For any inquiries or support‚ Mira customer service is available to assist. You can contact them via phone at the number provided on their official website or through email. Visit the Mira website for detailed contact information and operating hours. Ensure you have your product model number and purchase details ready for efficient assistance. Mira’s customer service team is committed to resolving your queries promptly and professionally.